Here is a list of "P" Codes - General Can-Am FAQ's - can-am ATV Forums - can-amtalk.com

Jump to content

 




 
 
 

Photo

Here is a list of "P" Codes


  • This topic is locked This topic is locked
23 replies to this topic

#1 ctuinstra

ctuinstra

    Advanced Member

  • Members
  • PipPipPip
  • 3318 posts
  • Gender:Male
  • Your Ride:.

Posted 05 November 2010 - 10:29 PM

Here is a list of the P codes. This is just the description of the P code. For more information, consult the service manual. These were take from the manual and I noticed there is a lot of repeat on the codes and some in the description. This should help to do a search of the code on this forum.

To read the active code, do the following before turning off the engine and clearing the code:

1) Turn the key to the lights ON position.
2) Use the mode button to scroll to the Engine Hour (EH).
3) Press the mode button once more and hold it while
4) Quickly (very quickly) toggle the HI LO switch. A minimum of 3 toggles within 2 seconds of pressing/holding the mode button.



If there is an active code, it should scroll across the display.

Enjoy!

P0106 Air pressure sensor voltage out of range.
P0107 Air pressure sensor voltage too low.
P0108 Air pressure sensor voltage too high.
P0111 Air temperature sensor functional problem.
P0112 Air temperature sensor voltage too low.
P0113 Air temperature sensor voltage too high.
P0116 Engine temperature sensor functional problem.
P0117 Engine temperature sensor voltage too low.
P0118 Engine temperature sensor voltage too high.
P0122 Throttle position sensor voltage too low.
P0123 Throttle position sensor voltage too high
P0231 Fuel pump open circuit or shorted to ground.
P0232 Fuel pump shorted to battery.
P0261 Cylinder #1 injector open circuit or shorted to ground.
P0262 Cylinder #1 injector shorted to battery.
P0264 Cylinder #2 injector open circuit or shorted to ground.
P0265 Cylinder #2 injector shorted to battery.
P0336 High engine RPM detected.
P0337 No cranshaft signal detected.
P0339 Cranshaft signal fault.
P0334 Cam phase sensor signal missing.
P0351 No ignition output stage Cylinder #1.
P0352 No ignition output stage Cylinder #2.
P0480 Engine fan short-circuit to battery.
P0480 Engine fan short-circuit to ground or open.
P0505 Idle air control valve output stage cutoff memory difference.
P0505 Idle air control valve output stage fault.
P0513 Incorrect DESS key.
P0520 Oil pressure switch functional problem.
P0562 Battery voltage too low.
P0563 Battery voltage too high.
P0600 CAN bus off.
P0600 CAN ID 514 missing.
P0601 Throttle position sensor adaptation failure.
P0601 Module call monitoring.
P0602 ECM not coded.
P0604 RAM fault.
P0605 EEPROM fault.
P0605 EEPROM checksum fault.
P0605 Coding ID checksum fault.
P0605 Coding checksum fault.
P0605 Programming checksum fault.
P0608 Sensor's power supply voltage too low.
P0608 Sensor's power supply voltage too high.
P0616 Starter relay open circuit or shorted to ground.
P0617 Starter relay shorted to battery.
P0705 Transmission range sensor circuit malfunction (PRNHL).
P1102 Throttle position sensor adaptation failure.
P1104 Throttle position sensor adaptation failure.
P1116 High temp.
P1148 Saftey fuel cut off detected.
P1202 Oil pressure switch still closed.
P1203 Oil pressure switch leakage.
P1520 Low oil.
P1655 DESS line shorted to battery.
P1656 DESS line shorted to ground.
P1675 Relay 2 shorted to battery.
P1676 Relay 2 open circuit or shorted to ground.
P1683 CAN RAM fault.
P2119 ECU wrong.

Sometime in the future I might list the entire section out of the manual.

Edited by ctuinstra, 28 February 2011 - 11:10 PM.


#2 Wolffmann34

Wolffmann34

    Aging Member

  • Members
  • PipPipPip
  • 4785 posts
  • Gender:Male
  • Location:Minnesota
  • Your Ride:Outty Xxc

Posted 05 November 2010 - 10:39 PM

Thanks CT.

Maybe we can get a MOD to pin this in the Tech threads.

Edited by Wolffmann34, 05 November 2010 - 10:40 PM.

2011 Outlander 800R Xxc
2012 RZR XP 900


#3 ctuinstra

ctuinstra

    Advanced Member

  • Members
  • PipPipPip
  • 3318 posts
  • Gender:Male
  • Your Ride:.

Posted 05 November 2010 - 10:57 PM

Thanks CT.

Maybe we can get a MOD to pin this in the Tech threads.

Yea, they get asked about a lot. Maybe this will help others if nothing else but a quick reference.

#4 25TH INFANTRY

25TH INFANTRY

    Advanced Member

  • Members
  • PipPipPip
  • 4531 posts
  • Gender:Male
  • Location:Cincinnati, Ohio
  • Your Ride:2010 Renegade XXC 800R //// 2011 Outty XXC 800R

Posted 05 November 2010 - 11:17 PM

Thanks CT.

Maybe we can get a MOD to pin this in the Tech threads.

X2
thats a nice little list, im going to print that out and have that with me on the trail. THANKS CT

#5 Wolffmann34

Wolffmann34

    Aging Member

  • Members
  • PipPipPip
  • 4785 posts
  • Gender:Male
  • Location:Minnesota
  • Your Ride:Outty Xxc

Posted 05 November 2010 - 11:24 PM

I saved it as a PDF on my phone :)

2011 Outlander 800R Xxc
2012 RZR XP 900


#6 Joe Clark

Joe Clark

    Advanced Member

  • Members
  • PipPipPip
  • 3019 posts
  • Gender:Male
  • Location:Illinois
  • Your Ride:2012 Renegade 1000

Posted 06 November 2010 - 12:13 AM

Hey CT...what does it mean when it says "167H"? :-D

Joe

#7 _M_

_M_

    Advanced Member

  • Members
  • PipPipPip
  • 97 posts
  • Gender:Male
  • Location:Springfield, Mo
  • Interests:Wheelin', wrenchin', and workin'
  • Your Ride:2009 Renegade 800r, Viper Red

Posted 06 November 2010 - 12:53 AM

Great Post!! Thanks! :-)

There is a mysterious bond between man and machine.


#8 rene1

rene1

    Advanced Member

  • Members
  • PipPipPip
  • 10839 posts
  • Gender:Male
  • Location:Alberta
  • Your Ride:2012 renegade

Posted 06 November 2010 - 12:57 AM

I saved it as a PDF on my phone :)



X2, got the whole manual on my iphone. the app is right beside my facebook app. hope it doesn't get a virus!! :wheelerdude:

awsome post chad!. this is very valuable info to have on hand. for anyone who has no manual, should print this off and keep it with there bike registration or something.


 

"My personality, is who I am. My attitude, depends on who you are."


#9 Renegade Dan

Renegade Dan

    Erect Member

  • Members
  • PipPipPip
  • 857 posts
  • Gender:Male
  • Location:Wausau, WI
  • Your Ride:Renegade 800, DS250, Moto 4 200, Chinese Chingling 110.

Posted 06 November 2010 - 01:02 AM

Thanks for posting Chad.

Hey Amos, how do you save and access PDFs on the phone? That could be handy for me...

#10 rene1

rene1

    Advanced Member

  • Members
  • PipPipPip
  • 10839 posts
  • Gender:Male
  • Location:Alberta
  • Your Ride:2012 renegade

Posted 06 November 2010 - 01:31 AM

down load the app "good reader". and it will walk you through it.


 

"My personality, is who I am. My attitude, depends on who you are."


#11 ctuinstra

ctuinstra

    Advanced Member

  • Members
  • PipPipPip
  • 3318 posts
  • Gender:Male
  • Your Ride:.

Posted 06 November 2010 - 07:41 AM

Hey CT...what does it mean when it says "167H"? :-D

Joe

That's the worst one of all. Time to buy a new ride! Or just press the mode button again.

#12 rene1

rene1

    Advanced Member

  • Members
  • PipPipPip
  • 10839 posts
  • Gender:Male
  • Location:Alberta
  • Your Ride:2012 renegade

Posted 06 November 2010 - 11:52 AM

That's the worst one of all. Time to buy a new ride! Or just press the mode button again.

So I guess 330h is a real bad one too then??


 

"My personality, is who I am. My attitude, depends on who you are."


#13 Wolffmann34

Wolffmann34

    Aging Member

  • Members
  • PipPipPip
  • 4785 posts
  • Gender:Male
  • Location:Minnesota
  • Your Ride:Outty Xxc

Posted 06 November 2010 - 08:03 PM

So is 26H acceptable?

2011 Outlander 800R Xxc
2012 RZR XP 900


#14 rene1

rene1

    Advanced Member

  • Members
  • PipPipPip
  • 10839 posts
  • Gender:Male
  • Location:Alberta
  • Your Ride:2012 renegade

Posted 06 November 2010 - 08:20 PM

actually i was off a little....

Attached File  9.JPG   263.09KB   32 downloads


 

"My personality, is who I am. My attitude, depends on who you are."


#15 OUTTY3

OUTTY3

    JBIRD

  • Members
  • PipPipPip
  • 13704 posts
  • Gender:Male
  • Location:Long Island NY
  • Interests:My kids, Quading, Snowmobiling.
  • Your Ride:12 Renegade 1000 Xxc

Posted 06 November 2010 - 09:49 PM

Thanks Chad, good to know.
12 Can Am Renegade 1000 Xxc/mods
16 Skidoo XRS 800 E-TEC coming soon.

 

#16 whitedogone

whitedogone

    Member

  • Members
  • PipPip
  • 27 posts
  • Your Ride:outty max

Posted 07 November 2010 - 09:23 PM

Here is a list of the P codes. This is just the description of the P code. For more information, consult the service manual. These were take from the manual and I noticed there is a lot of repeat on the codes and some in the description. This should help to do a search of the code on this forum.

To read the active code, do the following before turning off the engine and clearing the code:

1) Turn the key to the lights ON position.
2) Use the mode button to scroll to the Engine Hour (EH).
3) Press the mode button once more and hold it while
4) Quickly (very quckly) toggle the HI LO switch. A minimum of 3 toggles within 2 seconds.

If there is an active code, it should scroll across the display.

Enjoy!

P0106 Air pressure sensor voltage out of range.
P0107 Air pressure sensor voltage too low.
P0108 Air pressure sensor voltage too high.
P0111 Air temperature sensor functional problem.
P0112 Air temperature sensor voltage too low.
P0113 Air temperature sensor voltage too high.
P0116 Engine temperature sensor functional problem.
P0117 Engine temperature sensor voltage too low.
P0118 Engine temperature sensor voltage too high.
P0122 Throttle position sensor voltage too low.
P0123 Throttle position sensor voltage too high
P0231 Fuel pump open circuit or shorted to ground.
P0232 Fuel pump shorted to battery.
P0261 Cylinder #1 injector open circuit or shorted to ground.
P0262 Cylinder #1 injector shorted to battery.
P0264 Cylinder #2 injector open circuit or shorted to ground.
P0265 Cylinder #2 injector shorted to battery.
P0336 High engine RPM detected.
P0337 No cranshaft signal detected.
P0339 Cranshaft signal fault.
P0334 Cam phase sensor signal missing.
P0351 No ignition output stage Cylinder #1.
P0352 No ignition output stage Cylinder #2.
P0480 Engine fan short-circuit to battery.
P0480 Engine fan short-circuit to ground or open.
P0505 Idle air control valve output stage cutoff memory difference.
P0505 Idle air control valve output stage fault.
P0513 Incorrect DESS key.
P0520 Oil pressure switch functional problem.
P0562 Battery voltage too low.
P0563 Battery voltage too high.
P0600 CAN bus off.
P0600 CAN ID 514 missing.
P0601 Throttle position sensor adaptation failure.
P0601 Module call monitoring.
P0602 ECM not coded.
P0604 RAM fault.
P0605 EEPROM fault.
P0605 EEPROM checksum fault.
P0605 Coding ID checksum fault.
P0605 Coding checksum fault.
P0605 Programming checksum fault.
P0608 Sensor's power supply voltage too low.
P0608 Sensor's power supply voltage too high.
P0616 Starter relay open circuit or shorted to ground.
P0617 Starter relay shorted to battery.
P0705 Transmission range sensor circuit malfunction (PRNHL).
P1102 Throttle position sensor adaptation failure.
P1104 Throttle position sensor adaptation failure.
P1116 High temp.
P1148 Saftey fuel cut off detected.
P1202 Oil pressure switch still closed.
P1203 Oil pressure switch leakage.
P1520 Low oil.
P1655 DESS line shorted to battery.
P1656 DESS line shorted to ground.
P1675 Relay 2 shorted to battery.
P1676 Relay 2 open circuit or shorted to ground.
P1683 CAN RAM fault.
P2119 ECU wrong.

Sometime in the future I might list the entire section out of the manual.


Dang ;( .....how the heck am I going to remember all that at 5 am in 25 degree temps going 45mph in the dark.

#17 racer27

racer27

    Advanced Member

  • Members
  • PipPipPip
  • 176 posts
  • Gender:Male
  • Location:Berlin Wi
  • Interests:racing anything with a motor
  • Your Ride:can-am renegade 500

Posted 18 January 2011 - 12:25 AM

X2, got the whole manual on my iphone. the app is right beside my facebook app. hope it doesn't get a virus!! :wheelerdude:

awsome post chad!. this is very valuable info to have on hand. for anyone who has no manual, should print this off and keep it with there bike registration or something.


08 Rene 500
Custom Exhaust
Frogzskin's
ATR Spine
full BRP skids
warn 2500 winch
painted front fenders
can-am hand guards
27" Swamp Lites on ss'
25" Mud Lites on itp's
Stock rims and tires (Burnout tires)

looking to find an outlander to replace her...

#18 racer27

racer27

    Advanced Member

  • Members
  • PipPipPip
  • 176 posts
  • Gender:Male
  • Location:Berlin Wi
  • Interests:racing anything with a motor
  • Your Ride:can-am renegade 500

Posted 18 January 2011 - 12:28 AM

X2, got the whole manual on my iphone. the app is right beside my facebook app. hope it doesn't get a virus!! :wheelerdude:

awsome post chad!. this is very valuable info to have on hand. for anyone who has no manual, should print this off and keep it with there bike registration or something.

How did you get it on your phone? Im trying to put it on my droid but I can't figure it out.
08 Rene 500
Custom Exhaust
Frogzskin's
ATR Spine
full BRP skids
warn 2500 winch
painted front fenders
can-am hand guards
27" Swamp Lites on ss'
25" Mud Lites on itp's
Stock rims and tires (Burnout tires)

looking to find an outlander to replace her...

#19 CodyR

CodyR

    Advanced Member

  • Members
  • PipPipPip
  • 134 posts
  • Gender:Male
  • Location:Drayton Valley, Alberta.
  • Interests:Riding!
  • Your Ride:13' Outty 1000 , 09 Gade X 800 Mod

Posted 06 September 2011 - 11:13 PM

Thank you!

2-1.jpg
 


#20 bigboygadex

bigboygadex

    Newbie

  • Members
  • Pip
  • 4 posts
  • Your Ride:08 RenegadeX 800

Posted 16 October 2011 - 02:02 PM

Hey guts I was reading this thread to see if it could help me but it didn't, I have an 08 renx800 and I have the limp home mode and the check engine light on, I checked the batt terminals and they are fine, I had a bad thermostat that i changed, and I did the pcode test and it says no active codes. So i as all of you, What do I do next? any help would be great.
Thanks




1 user(s) are reading this topic

0 members, 1 guests, 0 anonymous users